| 2026-11-14 |
11:00 – 12:00 · 1h |
Finish cleaning tailstock parts; reassemble |
It looks like the front ball oiler is non-functional; ordering a replacement. Next up alignment. |
|
| 2026-11-13 |
45 min |
Dislodge live center; continue cleaning and disassembly |
Stainless steel drift through the back of the quill with electrical tape wrapped around it in two locations to protect the internal threads. Then some solid whacks with the 2 lb hammer after an overnight soak with PB Blaster. Then it popped out... Waiting on a larger wrench to get the screw retainer (LP-1222) off. |
|
| 2026-11-12 |
1h 15min |
Disassembly and cleaning of the tailstock |
Fairly straightforward. The only two hitches: the live center is wedged HARD in the tailstock spindle, and I don’t have a big enough wrench to register on the big nut at the hand wheel end. Both solvable in another session. |
|
| 2026-11-11 |
30 min |
First chips! |
A threading tool was the only thing I had at hand with close to the 0 rake for brass. |
|
| 2026-11-11 |
1h 30min |
Seated spindle in the bearings |
Clamped a faceplate against the far end of the headstock to keep the bearing in; pressed/tapped in the spindle from the front. The bearing shifted a bit; tapped it back into place with a block of wood guiding hammer blows alternating on each side of the spacer that bears against the bearing. And that's it! |
|
| 2026-11-10 |
1h |
Attempt to reinstall the spindle; problems |
The outboard bearing keeps pushing out and not wanting to be pushed back in with the spindle in place, which is where I'm stuck now. Solved one problem though: the back gear engagement mechanism needs to be appropriately timed. I had it wrong by happenstance and couldn't figure out why I couldn't disengage back gear regardless of plunger position. Pulled it out and rotated the eccentric start to its highest point, then slid the rack in place. That seems to work. |
|
| 2026-11-10 |
1h |
Finish fitting the bearings; wash the bore; oil the bearings |
Ended up giving it another good go with the flex hone, which got the job done. Nice running fit. |
|
| 2026-11-09 |
1h 30min |
Grinding the bore |
There’s one tight spot on the inboard side of the small end bushing. Can’t use the flex hone more without opening up the rest of it at the same time, so switching to a rotary tool. |
|
| 2026-11-08 |
1h |
Make 1/4-20 drill bushing; drill LA-119-1 in situ for dog point set screw |
Did not need to drill through; sufficient space for dog point within the steel wall of the gear. |
|
| 2026-11-07 |
15 min |
Seated LA-119-1 into the cone pulley |
Carefully hammered it in with wood bracing and a 2 lb engineer's hammer. |
|
| 2026-11-05 |
1h |
Test motor; reinstall on lathe; mount switch |
Motor ran beautifully. Ran it for 3-4 minutes, no warmth in the wiring in the box. Got it back on the motor mount with the help of an extra set of hands for the switch, but heck if I can figure out how it got positioned so all four bolts went through the mount! Will have to make some sort of adapter to extend the two rear flanges. But it works, forward and reverse and it is adjusted to drive the pulley on the countershaft. |
|
| 2026-11-04 |
2h |
Make the motor box joins; land cord and run on the rocker |
Everything is wired up and continuity tested; will plug it in and turn it on at the start of next session. |
|
| 2026-11-01 |
1h 30min |
Wire drum switch; pull old motor wiring; bring new run into motor box |
Drum studs: factory nut stays, then ring, cup washer (concave to ring), second nut. Start capacitor is the hump on top of the motor. Rocker: cord goes on the back two tabs, run 2 and 6 on the front. |
|
| 2026-10-31 |
30 min |
Opened motor wiring box; started prepping new wires |
|
|
| 2026-10-27 |
30 min |
Open and measure drum switch contacts |
Source wire and conduit to match |
|
| 2026-10-25 |
45 min |
Clean and reattach LA-255 and threading dial |
Threading dial was just WD-40 and elbow grease to keep from getting water into the mechanism; LA-255 was the usual protocol: Simple Green, scrub, WD-40, scrub, rinse, dry, attach. |
|
| 2026-10-24 |
5 min |
Set end shake on the lead screw. |
.003 seems good, but we'll see when it's under power. |
|
| 2026-10-24 |
15 min |
Troubleshoot half nut |
Fixed it; it was just on upside down so the female threads were pointed the opposite direction of the male threads on the lead screw. Easy fix. |
|
| 2026-10-23 |
45 min |
Reinstall lead screw |
Went on great, engages with the cross feed. Only problem is that the rebuilt half-nut doesn't engage with it. A problem for another day. |
|
| 2026-10-23 |
1h |
Clean lead screw |
Finished getting all the packed gunk out, full length. Needs a once over with WD-40 then it's done. |
|
| 2026-10-23 |
1h 15min |
Cleaning lead screw and attachments |
Up to 18" clean; and the gears, key, spacer, and nut that go on the end are also clean. Progress on the cast guard that bolts over it. |
|
| 2026-10-22 |
30 min |
Cleaning the lead screw |
Up to 11" clean now. |
|
| 2026-10-22 |
20 min |
Change out pulley on motor shaft |
Pulled the old one with little difficulty; filed damage off key stock; installed new Logan two-step pulley. Belt no longer fits, which is not surprising given different pulley size. |
|
| 2026-10-20 |
15 min |
Press on cone pulley bearing parts |
0793 went in with my veneer press screw; the LA-119-1 went in slightly, but I can't apply enough pressure with my veneer press to get the interference fit home. |
|
| 2026-10-18 |
14:20 – 15:45 · 1h 25min |
Clean second change gear stack; remount change gear banjo. |
|
|
| 2026-10-18 |
15:45 – 16:15 · 30 min |
Cleaning the lead screw |
Slow work with a popsicle stick planed to the profile of an acme thread. 6" down; 24" to go. |
|
| 2026-10-18 |
11:15 – 12:00 · 45 min |
Clean and remount headstock side lead screw bracket; clean change gear banjo |
Change gear banjo was probably the dirtiest part I've pulled off of this. Layers and layers of gunk. |
|
| 2026-10-18 |
09:00 – 09:45 · 45 min |
Cleaned and re-mounted the gear cover; cleaned LA-167 |
Surprisingly little gunk on the gear cover for its size. |
|
| 2026-10-17 |
2h |
Disassemble, clean, re-assemble LA-4 (reverse gear assembly) |
Had to jam a wooden wedge in the gears to get enough resistance to get them unbolted; smooth other than that. Usual combination of Simple Green, ultrasonic cleaner, EvapoRust, and a toothbrush. Each as needed. |
|
| 2026-10-17 |
45 min |
Attempt to free front bushing collar; clean bull gear. |
Couldn't get the collar free with a hook wrench; got good purchase on it, but couldn't apply enough force. Cleaned everything up and I'll re-install without checking the bearing. If it gives problems I'll take it back apart and work harder on getting it out. |
|
| 2026-10-12 |
15 min |
Freed pulley gear! |
Got the bearing puller on it, flipped it, rested it on the jaws of my woodworking vise, put a 1.25" diameter aluminum rod through the back, and pounded it out. The aluminum registered on the underside of the jaws of the bearing puller, and that was sufficient to force it out. |
|
| 2026-10-12 |
1h 15min |
Cleaned interior of the headstock |
Each gear tooth with a popsicle stick and paper towel; could not get good access to the back gear engagement gear in situ; just brushed off and WD-40'd, everything else was scrubbed. |
|
| 2026-10-11 |
1h 30min |
Pulled LA-119-1's bushing; struck out pulling the gear |
Internal bushing puller eventually got the bushing after heavy grinding to the arms of the tool to fit; no joy on getting the gear itself. There's a place for the puller to register, but couldn't apply enough force. Tried heating the cone pulley to get it to expand. |
|
| 2026-10-11 |
30 min |
Remount miter gear and way wipers |
Mating miter gear had tooth damage preventing smooth operation; removed and filed down mushrooming. Worked great. Way wipers soaked in way oil and screwed back in. |
|
| 2026-10-10 |
45 min |
Clean and reassemble the apron miter gear and bracket |
Probably need to unmount the carriage to get it mounted back in appropriate mesh. |
|
| 2026-10-01 |
1h |
Disassemble the spindle |
More force than expected needed to get it out. Clamped a bar across the change gear end of the spindle, hammered, tightened the clamps, tightened some more, hammered some more. Front bearing came out with the nose; rear bearing stayed put. Wooden wedge between bull gear and casting so its teeth weren’t taking the force of the hammer strikes on the end. |
|
| 2026-09-30 |
30 min |
Reassemble compound |
Reamed the handle hole to remove broken pin stub. Appears to be holding just fine without a key. |
|
| 2026-09-29 |
1h 45min |
Clean the compound |
Simple Green, EvapoRust, and a lot of scrubbing. Lots of gunk to come off. |
|
| 2026-09-28 |
15 min |
Final compound disassembly |
Figured out the compound nut (LA-697) extraction. It rotated freely after a bath in PB Blaster. Downward pressure from an old flat head screwdriver on the TOP of LA-697 rather than through the threaded hole with a popsicle stick backing it to protect the threads in the casting. |
|
| 2026-09-28 |
10 min |
Freed LA-254 (compound rest bushing) from compound rest |
Pin spanner was the tool for the job. Next puzzle is LA-697 (compound rest nut). |
|
| 2026-09-26 |
40 min |
Repair compound rest top threads |
Thread repair die worked great. Thread damage likely the result of 273 shearing off and mangling the thread as 271 continued to rotate. Next step is figuring out how to get 254 off. |
|
| 2026-09-23 |
1h |
Clean and install cross slide screw cover; start disassembly of swivel; mangled thread has trapped one of the jam nuts; ordered rethreading die. |
|
|
| 2026-09-22 |
1h |
Clean and reattach the cross slide handle assembly. |
|
|
| 2026-09-20 |
45 min |
Reassembled apron; addressed gear mesh issue (filed damage off of gear), reattached to carriage. |
|
|
| 2026-09-20 |
45 min |
Stoned the burrs off of the ways. |
|
|
| 2026-09-19 |
1h |
Free compound slide from cross slide; ground new flats on rounded over nuts in place, used next smallest wrench. |
|
|
| 2026-09-17 |
1h |
Disassemble, clean, reassemble the half nut assembly. |
|
|
| 2026-09-14 |
30 min |
Cleaned last portion of saddle casting, set back in place. WD-40 great solvent for this. |
|
|
| 2026-09-13 |
3h |
Cleaning the saddle |
|
|
| 2026-09-11 |
2h |
Reassemble drive box; align hinges; clean involved hardware; temporarily elevate leg to match adjustable feet. |
|
|
| 2026-09-09 |
1h |
Flip chip pan, derust, reattach motor mount after getting it back from the welder. Appears to be fixed. |
|
|
| 2026-09-04 |
1h |
Clean the bed; dismount the drive box; dropped it off the crane and broke the countershaft yoke. Very frustrating! |
|
|
| 2026-09-03 |
1h |
Finish cleaning motor housing and related bolts; remount motor housing. |
|
|
| 2026-09-02 |
30 min |
Clean motor housing |
|
|
| 2026-08-30 |
1h |
Clean and remount countershaft. |
|
|
| 2026-08-30 |
1h 30min |
Scrub drive housing; remount on headstock. |
|
|
| 2026-08-29 |
45 min |
Scrub drive housing & nuts; reassemble 3-jaw |
|
|
| 2026-08-28 |
1h |
Disassemble and clean the 3-jaw; need chuck grease. This was made to very tight tolerances, pleasantly surprised. |
|
|
| 2026-08-28 |
45 min |
Scrubbed front of the bed casting. |
|
|
| 2026-08-25 |
1h |
Cleaning brackets; oiling; reinstall. Remove flywheel on countershaft. Flash rust really a thing on those bolts! Dry and oil ASAP. |
|
|
| 2026-08-25 |
30 min |
Remove and wash brackets; start wash of back of headstock. 1:1 Simple Green & denture brush. |
|
|
| 2026-08-23 |
4h |
Finished disassembly, moved to shop, attached bed to legs. |
|
|
| 2026-08-22 |
4h |
Disassembly. Detached the tailstock, carriage, lead screw, headstock cover. Further disassembly on the carriage. |
|
|